88ÿéÕ ALL CODE AFTER THIS POINT IS COPYRIGHT WOOLF SOFTWARE SYSTEMS (C) 1981 REPRODUCTION BY ANY MEANS PROHIBITED BY LAW. ALL RIGHTS RESERVED  0¢¾ 0¢À 0¢ä 0¢æºuèú ºÉèô è¢ ŠÁ Àuè »2#º\µŠ‹úªŸCžŸBžþÍuñéè »s#º\èf  q Àt ºžèµ èê éµÿº€è 2À¢h¢i¢j¢k¢|º\è² þÀu º6èˆ é# »AµèÑ ¢r …DŠð :Æu  †DŠð :Æt º è\ é÷»R#º\µŠ‹úªŸCžŸBžþÍuñ2À¢h¢i¢j¢k¢|º\èK þÀu ºµ è! é¼»0èl º\è: º0è èº »s#èƒ ŠÃŸ†àP†àè0 X†àž ŠÁ ÀtèHˆCºrèz  C<È°t°è«è ŠÁ Àtè$‹Å Àu°té°u¢C¢/C»:CSº£èC ²(è6 ŠŸCžè˜²,è) ŠGèŠèˆ²)è ² è èÊŠÁµ Àtèºs<ué–ºÚèÿ µé[CCCSé [ˆ7ŸCž‰/ŸCCžSµºmèÝ [S²(èÎ ŠŸCžè0²,èÁ ŠGè%Šè ²)è± ² è¬ èbŠÁ ÀtèTs<t3ºÚèœ é¶ÿ[CCCSé [ˆ7ŸCž‰/ŸCCžSþÅŠÅ<té–ÿ[º2èr é [ŠÅ¢9Cº èc èŠé°P*Å ÀÐØ»žBŠèÆ ŸCžþÍuö‡Ú r#Šè Àt»s#Š‹úªŸCžŸBžþÍuñ° ‹úªŸBž° ‹úªŸBž‹úªŸBž°$‹úªéééç»b#º\µŠ‹úªŸCžŸBžþÍuñ2À¢h¢i¢j¢k¢|º\èäþÀu º!èºéU»0èº\èÓº0è¥èS»s#èŠÃŸ†àP†àèÉX†àž to leave value unchanged: $ Please enter the status port to use (in hex), or to leave value unchanged: $ Next, enter the transmit buffer empty mask, or to leave value unchanged: $ Next, enter the receive buffer full mask, or to leave value unchanged: $ Please enter the polarity of the transmit and receive status bits. If the documentation you are using specifies that the status bits are 1 type 1. Otherwise, type 0. If you are in doubt, enter a 1. Please enter the polarity of the status bits: or to leave value unchanged: $ Next, enter the initialization bytes your serial card requires (if any). The bytes are entered in two number pairs. The first is the data to send, and the second is the port to send the data to. For example, to send an AA to port 0005, enter the information as: AA,0005 and then press the return key. To signal the end of the list, press the key. Please enter the initialization bytes, or to leave value unchanged: $ $ Lastly, enter a description line to define this version of MOVE-IT. This line will be inserted in the sign-on message to identify your configuration. For example, the line might be: (For Seattle 4-Port I/O board, at 9600 baud) Please enter the description line: $ This concludes the configuration for MOVE-IT. If you wish, CONFIG can test the newly created version to make sure the output and input sec- tions function properly. Testing the I/O section requires that the user build a special connector that connects the trans- mitter and receiver together. If you are using a modem with MOVE-IT, there may be a switch called "loopback". If so, you can just flip this switch. If you're going to connect up MOVE-IT via a wire or your modem has no switch, you will need to make and install a special connector and plug it into the serial socket. The diagram for this cable is in the manual. Do you wish to test the I/O section? $Plug the special connector into the socket on your computer and then press return.$ Testing communications section... $The bits that were specified for transmit buffer empty do not appear to be working properly. Either the wrong status port was specified, or the transmit buffer empty mask was specified incorrectly. Try again? $The bits that were specified for receive buffer empty do not appear to be working properly. Either the wrong status port was specified, or the receive buffer empty mask was specified incorrectly. Also, this could occur if the special connector was not installed or was made incorrectly. Try again? $The status bits appear to be working, but the data that was sent out doesn't match the data that came in. This could occur if the special connector was made incorrectly or the init- ialization was incorrectly performed. Also, this could be caused if the initialization bytes specified less than 8 data bits, or parity. Consult your hardware manual for more information. Try again? $Everything appears to be working correctly. Press return to save your configured version of MOVE-IT... $ Please enter the data and port bytes in two number pairs, separated by a comma. $ There is only room for 20 data/port pairs in the initialization table. If you need more than this, you'll probably need to write a custom I/O section for MOVE-IT. See the user's manual for more information. $ You are trying to use this version of Mconfig on the wrong version of MOVE-IT! You must use the version of MCONFIG which matches the same version of MOVE-IT. $ The file VERSIONS.CNF is not on the default disk. This file must be present to configure MOVE-IT. $ The file VERSIONS.DIL is not on the default disk. This file must be present to support auto-dialing. $ The .CNF file for the configuration you selected is not present on the default disk. Is the right disk loaded? $ The .DIL file for the modem you selected is not present on the default disk. Is the right disk loaded? $ Number out of range. Try again. $ Move-it normally allows a remote user to change user areas on the local system. Do you wish to allow remote access to other user areas? $MOVE-IT UCFMOVE-IT CMDVERSIONSCNFVERSIONSDIL