22Cs YOU ARE TRYING TO RUN AN UNCONFIGURED MOVE-IT! RUN MCONFIG FIRST.  $2 PXÐú$u2úú$u2úC ALL CODE IN THIS PROGRAM IS COPYRIGHT WOOLF SOFTWARE SYSTEMS (C) 1981 REPRODUCTION BY ANY MEANS PROHIBITED BY LAW. ALL RIGHTS RESERVED. 0*0*X)=)2F)E)A)%a) t,CCE) uǰ^)9"QP) XY t? *2 C t!ЊЊ؟Cڋޞ9*>!RONP) s@) u2@)<u'&!ZCSC <t< t <,uC[r SQY[Z>q?<t06t 7>}C< t<u C< t<uISQC<,t#uC<,u uY[Ê< u <tvCCȟCSЊBЊ؟CB t;ޞ֊ t BB؟BZR[r< t C<,u[OD.EV3NO8HABFUGALQECnPRXO2H) 2G) sr|T\C u y QRC?Cu.3,CuCCCCZYðG\)^)C u< uCS tşC u J u [2<)9)PQSR [YW)<t629)^)G\)?\BCu2|h\ ur \w  u "]X)S[W)<t429) SX[5 W)<tr u"9)p3yX)XZRPU) t2U)N>PQRS&&صPQRSڻ}&&ڵ/S&C7[ޞrЊЊПBޞևڋ&CC&ڊu[ZYXRQڻ tF,0rBr>yr6 ȵޞ֟ޞ֟ޞ֟ޞ֟ޞ֟BYZRQ< uCڋ,0"x9< r4BޞSޞ֟ޞYޞ֊ȵޞYZSRQP2B)X?SRQ2B)?gr$<t/<t+< tH< r韆PB)YZSRQ ]SRQUSRQMSRQESRQ=SRQ5SRQ-SRQ%SRQSRQSRQ SRQ SRQYZ[A * * MOVE-IT (tm) * * Inter-computer communications utility Version 0.0 Copyright (c) 1982 Woolf Software Systems Serial number $ $ **** File Not Found $ **** Syntax Error! The proper commands are: Send FILNAME.TYP [AS DESTNAME.TYP] (Send file to remote computer) Get FILNAME.TYP [AS DESTNAME.TYP] (Get file from remote computer) LDir FILNAME.TYP (Get local directory) RDir FILNAME.TYP (Get remote directory) LUser [USER NUMBER] (Get/Set local user number) RUser [USER NUMBER] (Get/Set remote user number) Call [NUMBER] [NAME] (Call number or name) Hangup (Hang up the phone) ANswer (Answer the phone) NOConsole (Inhibit console output) Binary (Set 8 bit transmission mode) AScii (Set 7 bit transmission mode) Message [MESSAGE TO SEND] (Send message to remote console) TRies (Display retries) TAlk [FULL] [HALF] [EVEN] [ODD] [NOPARITY] (Enter smart terminal mode) Exit (Exit to Operating System) $ Escape sequence not found. Valid sequences are: Send 1 escape to remote computer S Send a file to the remote computer G Get a file from the remote computer A Toggle Auto Line Feed on/off C Toggle remote echo on/off T Toggle file trapping on/off P Toggle printer on/off X Change XON and XOFF characters. E Exit Talk Mode (Return to prompt). $ File name already exists on remote end. Replace?$ File name already exists on local end. Replace?$ Remote disk full. Insert new disk and press return to continue, or press control-c to exit to Operating System. $ Remote directory full. Insert new disk and press return to continue, or press control-c to exit to Operating System. $ Disk full. Insert new disk and press return to continue, or press control-c to exit to Operating System. $ Directory full. Insert new disk and press return to continue, or press control-c to exit to Operating System. $ Disk full. $Sending $Receiving $...$ Complete.$ Aborted.$ Aborted. Directory full. $ Aborted. Disk full. $ Remote computer timed out. Command aborted. $ Warning - When an ambigious name is transferred, only the drive name is permitted in the "AS" field. File name ignored. $ Communications Line Failure. Either the comline is down or the remote computer is no longer running the utility. Try Again?$Directory for local disk $Directory for remote disk $Receiving filenames, please be patient... $Sending filenames...$ Message from remote computer: $ Number of retries: $ Do you want to clear the retry counter? $ Remote user number: $ Local user number: $ Filename to send to remote computer?$ Filename to get from remote computer?$ Please enter the letter that describes the protocol you wish to use (N,E,C,T,X,?), or press Return to abort. $ Valid protocols are: N - No protocol. Characters are send at full speed, with no pauses. E - Echo wait. 1 character is sent and then checked against the echo from the remote computer. If an error is found, the user can ignore it or abort the transfer. C - Character wait. One line is sent, then local computer waits for the specified character from the remote computer. T - Time wait. One line is sent, then the local computer waits for 1 second. X - XON/XOFF. Characters are sent until remote computer sends XOFF, and resumed when remote computer sends XON. Please consult the users manual for more information. $ Please enter the character to wait for: $ Transmission in progress... $ [Transmission complete.]$ [Transmission aborted.] $ [Transmission suspended] $ [Transmission resumed] $ [Saving data to disk...$ Done.] $ Invalid option: $Valid options are: HALF, FULL, NOPARITY, EVEN, ODD$Current settings are: $Half Duplex, $Full Duplex, $No Parity.$Even Parity.$Odd Parity.$ [Auto Line Feed is on.] $ [Auto Line Feed is off.] $ [Printer is on.] $ [Printer is off.] $ [File trapping is on.] $ [File trapping is off.] $ There is no file open to accept the trapped data. Use G to open a file. $ The remote computer echoed the wrong character. Press return to ignore and continue, or Control-Z to abort. $ The current values for XON and XOFF are: XON: $ XOFF: $Please enter the new value for XON: $and for XOFF: $ New values accepted. $ [Remote echo is on.] $ [Remote echo is off.] $ Sorry, the remote computer does not support this command.$ Size of trapping buffer: $ characters.$ $.... Working ....$                 $An error exists in the switches for the name called. Command aborted. $Name not found in PHONE.NUM! $ There is data in the trapping buffer. Do you wish to save it? $[Trapping file is now open.]$ Not enough memory for function. $ Valid names i