.op
.po2
*****************************************************************

Wordstar installation for the Hewlett Packard computer.
The example has a COPY of the Wordstar disk in drive B:

******************************************************************

B>INSTALL




  COPYRIGHT (C) 1981  MicroPro International Corporation  

 INSTALL version 4.2  for MicroPro WordStar release 3.00        


Do you want a normal first-time INSTALLation of WordStar?
(Y = yes;  N = display other options): Y


This will INSTALL the WSU.COM on the current drive, save
the result on file WS.COM on the current drive, and then
run the INSTALLed WordStar.  OK (Y/N): Y



  MicroPro WordStar  release 3.00  serial # WS(your s.n.)      


      *****  WordStar TERMINAL MENU #1  *****

A  Lear-Siegler ADM-3A        C  Lear-Siegler ADM-31
D  Hazeltine 1500             E  Microterm ACT-IV
F  Beehive 150/Cromemco 3100  G  Imsai VIO
H  Hewlett-Packard 2621 A/P   I  Infoton I-100
J  Processor Tech Sol / VDM   K  Soroc IQ-120/140
L  Perkin-Elmer 550 (Bantam)  2  Terminal Menu #2
3  Terminal Menu #3           Z  none of the above
U  no change

PLEASE ENTER SELECTION (1 LETTER): H

HEWLETT-PACKARD 2621 terminal

OK (Y/N): Y





            *****  PRINTER MENU  *****
(More specific info is displayed after choice is entered)

A  Any "Teletype-like" printer (ie almost any printer)
C  "Teletype-like" printer that can BACKSPACE
D  DIABLO 1610/1620 daisy wheel printer
E  DIABLO 1640/1650/630/Xerox 1700 series daisy wheel printer
F  QUME Sprint 5 daisy wheel printer
G  NEC Spinwriter 5510/5520 thimble printer
I  "Half-Line-Feed" Printers
M  I/O Master / O.E.M. Printer Combination
R  C. Itoh/TEC Starwriter Printer
U  no change
Z  none of the above

PLEASE ENTER SELECTION (1 LETTER): C

Backspacing TTY-like printer

    This choice is for any printer that will respond to an
Ascii BACKSPACE character (code 08) as well as carriage
return, line feed, and printing characters.
    Make sure any AUTO LF or LOCAL LF switch is OFF.
    If you have a DAISY WHEEL or thimble printer shown on the
menu, use the appropriate choice in order to obtain "Micro-
justified" output and additional formatting capabilities.
    Refer to manual for instructions on patching in optional
control sequences for ribbon color change, character pitch
change, and half-line roll (for subscripts and superscripts)
if your printer has these capabilities.

OK (Y/N): Y





Most Teletype-like printers use no communications protocol.

       *****  COMMUNICATIONS PROTOCOL MENU  *****

A "Communications Protocol" is necessary with some printers
to prevent printer buffer overflow and character loss.

E  "ETX/ACK" Protocol
X  "X-ON/X-OFF" Protocol
N  NONE required (or handled outside of WordStar)
U  no change

PLEASE ENTER SELECTION (E, X, N, B, or U): N

No communications protocol


OK (Y/N): Y





With no protocol, the usual driver selection (below) is L

           *****  DRIVER MENU  *****

Or, how should WordStar send characters to your printer?

L   CP/M "List" device (LST:)
T   CP/M primary console device (TTY:)
C   CP/M secondary console device (CRT:)
P   Port Driver (direct I/O to 8-bit ports)
N   Parallel Centronics Printer Driver
Q   Serial Driver on TRS-80 Model-2
S   User-installed driver subroutines
U   no change

PLEASE ENTER SELECTION (L,T,C,P,N,P,S,B or U): L

CP/M List Output driver (LST:)


    In most systems this is a "logical" device which must be
assigned to the desired one of four "physical" devices with
the STAT command, before WordStar is invoked.

OK (Y/N): Y






ARE THE MODIFICATIONS TO WORDSTAR NOW COMPLETE?

  IF THEY ARE ANSWER YES TO THE NEXT QUESTION.
  IF YOU WISH TO MAKE ADDITIONAL PATCHES TO WORDSTAR'S
  USER AREAS, ANSWER NO TO THE NEXT QUESTION.


OK (Y/N): N



YOU MAY NOW MODIFY ANY LOCATION DESCRIBED IN THE LISTING
AT THE END OF THE USER MANUAL OR THE CUSTOMIZATION NOTES.

YOU MAY USE EITHER THE LABEL OR THE HEX ADDRESS TO SPECIFY
THE LOCATIONS YOU WISH TO CHANGE.  IF YOU USE A LABEL THEN
YOU MAY APPEND AN OFFSET TO THE LABEL (I.E. LABEL:+31). THE
LABEL ALWAYS HAS A ":" APPENDED (LABEL:). YOU MAY SPECIFY
THE NEW VALUE ONLY AS A HEX NUMBER.  A LOCATION OF ZERO (0)
WILL CAUSE THE END OF THE MODIFICATIONS


LOCATION TO BE CHANGED (0=END): 284
    ADDRESS : 0284H   OLD VALUE: 04H   NEW VALUE: 00
LOCATION TO BE CHANGED (0=END): 28B
    ADDRESS : 028BH   OLD VALUE: 04H   NEW VALUE: 00
LOCATION TO BE CHANGED (0=END): 2D1
    ADDRESS : 02D1H   OLD VALUE: 19H   NEW VALUE: 03
LOCATION TO BE CHANGED (0=END): 2D2
    ADDRESS : 02D2H   OLD VALUE: 40H   NEW VALUE: 07
LOCATION TO BE CHANGED (0=END): 2D3
    ADDRESS : 02D3H   OLD VALUE: 09H   NEW VALUE: 03
LOCATION TO BE CHANGED (0=END): 0



CONFIRM TERMINAL AND PRINTER SELECTIONS:

 HEWLETT-PACKARD 2621 terminal    
 Backspacing TTY-like printer     
 No communications protocol       
 CP/M List Output driver (LST:)   

OK (Y/N): Y

******************************************************************

The installation is now complete and the WS.COM file will
be written to the logged in disk.

For users that wish to play with the highlighting, patch
the above locations with the following data instead of the 00's
See page number 9 of appendix E from the 3.0 manual. 

IVON: 0284H - 04,1B,26,64,48

IVOFF: 028B - 04,1B,26,64 40