This disk contains the following files:

NWINSTAL.COM   Installation program.  It will prompt you through 
               installing NewWord for your terminal and printer.  
               You also personalize NewWord with this program.

NWU.COM        NewWord:  Pre-installed for a Televideo 925 and a 
               draft printer.  (Many other terminals can be run 
               by this configuration: Lear Siegler ADM-31, ADM-
               22, WYSE 100, Qume 102.)  

NW.OVR         Main NewWord overlay.

NWPRINT.OVR    NewWord printer drivers.

NWMSGS.OVR     Messages and menus.

PRACTICE.DOC
SAMPLE1.DOC    Practice files for the Tutorial: Do It Yourself
SAMPLE2.DOC

READ-ME        This document.





                  Tips on printer installation:  

NewWord cannot be installed to use your printer unless the opera-
ting system can print on it correctly.  Auto line feed must be 
disabled on your printer.  To test whether your system can print 
properly, put a disk containing this file in drive A (varies with 
the system), ready your printer and enter:

PIP LST:=READ-ME

If this document is printed single-spaced with no characters 
lost, NewWord can be installed to use your printer.  If it isn't 
printed correctly, you must customize NewWord to run your printer 
(see appendix C of the NewWord Encyclopedia).














There are several printer drivers in NWPRINT.OVR:


                  NON-SPECIFIC PRINTER DRIVERS

SIMPLE    This driver does not support print enhancements (bold, 
          double-strike, underline, strike-out).  It should only 
          be used if the other drivers won't run your printer, or 
          to make a quick review copy.  Printers which advance 
          the paper to print (Printronix, Versatec, Gould, etc) 
          must use this driver.

DRAFT     Most dot matrix printers.  This driver implements the 
          print enhancements by carriage return and overprinting.  

TYPEWR    Typewriters and many backspacing printers.  Print 
          enhancements are done by backspacing and overprinting.  
          If your printer can backspace and isn't directly 
          supported by one of the other drivers, you should test 
          both this driver and the DRAFT driver to see which 
          prints faster (or better).


                         WHEEL PRINTERS

D1610     Most Diablo (and Diablo emulating) daisy wheel
          printers. The Diablo 620(some), 630(some), 1610, 1620, 
          1640 and 1650 can be run successfully by this driver.

D630      Actually the 1610 printer driver.  It will drive most
          Diablo 620 and 630 daisy wheel printers.  

QSPR11    Actually the 1610 printer driver.  QUME Sprint 5,7,9 & 
          11 daisy wheel printers.

SR550     Silver Reed daisy wheel printers.

N2000     NEC 2000 series thimble wheel printers.

N3500     NEC 3500 series thimble wheel printers.

N5500     NEC 5500 series thimble wheel printers.













                  SPECIFIC DOT MATRIX PRINTERS

MX80      Epson MX and FX series printers.  This driver supports 
MX100     microspace justification for flush right margins, 
          different character widths (.cw n), different line 
          heights (.lh n), sub and superscripts.  Microspace 
          justification is done by adding space between words in 
          1/60 inch increments.

MT160L    Mannesmann Tally MT160L dot matrix printer.  This 
          driver supports  different character widths (.cw n), 
          different line heights (.lh n), sub and superscripts,  
          Text is printed in correspondence mode for 10 and 12 
          pitch; draft mode for other character widths.  Text is 
          NOT microspace justified.

OKI84     Okidata microline model 84 (step 2), 92 and 93 dot 
OKI92     matrix printers.  This driver uses the correspondence 
OKI93     mode to produce very high quality output.  Print speed 
          is reduced from draft mode.  This driver supports 
          microspace justification for flush right margins, 
          different character widths (.cw n), different line 
          heights (.lh n), sub and superscripts.  There is a 
          limit of 10 inches of print space for the model 84 
          printer when using 17 pitch (.cw of 9 or less).  Use 
          the draft driver and custom print controls if you wish 
          to print at 17 pitch with more than 170 characters.  
          For the model 92 and 93 printers, .cw of 9 or less 
          switches to draft mode and .cw of 15 or more doesn't 
          work accurately.  Older models of the 84 and other Oki 
          printers may not be run successfully by this driver.

C1550     C.Itoh Prowriter models 8510 and 1550.  This driver 
          supports microspace justification for flush right 
          margins, different character widths (.cw n), different 
          line heights (.lh n) and sub and superscripts.

You can install which printer driver NewWord will use as its 
default with NWINSTAL.  You may always select a different printer 
when you are ready to print.  You might use this to advantage, 
for example, by installing the DRAFT or SIMPLE printer as the 
default, then using the enhanced driver for final copies.