@DefineProject
	@NAME 		= "ReadRight (R)"	/* MASTER 3 1/2 or HI DENSITY  */
	@VERSION	= "Windows" 
	@SUBDIR 	= "\\OCR\\"
	@OutDRIVE 	= C
	@Requires	5000000
	@Requires	@HardDisk
@EndProject

@Welcome
	@CLS
	@If (@OSMajor < 3)
	@Name requires DOS version 3.0 or higher.

	@Pause
	@Abort
	@Endif

	IT IS A FEDERAL CRIME TO MAKE UNAUTHORIZED COPIES OF THIS SOFTWARE

	Federal copyright law permits a registered user to make a backup
	of this software for archival purposes only.

	Any other duplication and distribution of this software, including
	copies offered through sale, loan, rental, or gift, is a violation
	of law, and subject to both criminal and civil penalties.

@Pause
@Cls

	This program will install ReadRight (R) for Windows on your com-
	puter's hard disk drive. You will be prompted for the following in-
	formation:
		
		- Disk Drive 

		- Subdirectory

		
	Then the install program will prompt you to insert your copies of
	the master disks. At any time during the installation, you can abort
	the process by pressing the [Esc] key.

	IMPORTANT! If you have not already made copies of your master disks,
	stop the installation program now by hitting the [Esc] key and make
	backup copies.

@Pause

@EndWelcome


@GetOutDrive
	@CLS

	On which hard disk drive do you wish to install @NAME:

















	Use the arrow keys to highlight your selection, 
	and then press [Enter].
@EndOutDrive

@GetSubdir
	@CLS

	Now you need to specify the destination subdirectory. The 
	subdirectory is the location on your disk where @NAME
	will be installed.  
	
	For the standard installation, just press [Enter].

	@PROMPT = "Which subdirectory ?"
@EndSubdir


@DefineDisk
	@LABEL = "Disk 1 Installation"

	@BeginLib DRIVER.WIN

		@File CH3P_WIN.DLL
		@File CN_IX12.DLL
		@File CN_IX30F.DLL
		@File CPC_FLAT.DLL
		@File EPS_WIN.DLL
		@File HPW.DLL
		@File PANAWIN.DLL
		@File MHELP.DLL
		@File MSCAN.DLL
		@File MTEK.DLL
		@File MTEK_ADF.DLL
		@File SCANNER.INF
		@File IXHND2.COM
		@File MEISCAN5.COM
		@File MEISCAN6.COM
		@File MEISCAN7.COM
		@File SI3.SYS
		@File SJDRIVER.SYS
		@File CPCFSCAN.SYS
		@File MSCAN.SYS
		@File EPSN.SYS


	@EndLib

	@File RRDATA.DLL
	@File DEFAULT.SET
	@File RRDFLT.SET
	@File README.TXT
	@File USERSGD.TXT
	@File SAMPLE.TIF
	@File PROG.001 @Out RR.EXE @Decompress
		
@EndDisk		


@DefineDisk
	@LABEL = "Disk 2"

	@File PROG.002 @AppendTo RR.EXE @Decompress
	@File Microtek.exe

	@BeginLib SPLLHELP.WIN

		@File RR.HLP
		@File AM0100.DSK
		@File AM0110.DSK
		@File AM0110.RAM
		@File SM10.RAM

	@EndLib

@EndDisk



@Finish
@Cls
	In order for @Name to function properly, the "FILES="
	and "BUFFERS=" settings in your CONFIG.SYS file must be at
	least 20 and 15 respectively.  If your CONFIG.SYS file does
	not have an entry for these settings or these settings are too
	low, add the following lines to your CONFIG.SYS file:

		FILES = 20
		BUFFERS = 15
@Pause
@Cls

	@Cls

	IMPORTANT for all ReadRight users:
	ÄÄÄÄÄÄÄÄÄ

	To run ReadRight your system must have at least 4,000,000 bytes
	of free system memory.  

	HIMEM.SYS and SMARTDRV.SYS are required to run ReadRight.  When
	running in 386 Enhanced Mode, it is also suggested that you install
	a permanent Swap File.
	@Pause
	@Cls

@Cls








			Installation Successful
                   Be sure to read C:\OCR\README.TXT
@Pause
@EndFinish