#---------------------------------------------------------------------------#
# SirlinVIEW Viewstation Configuration File
#
#	This file can be edited to change the Viewstation software
#	configuration. 
#
#	Lines starting with the pound-sign, "#", are commented out
#	(that is, the rest of the line is ignored), and the standard 
#	values are shown. To change a definition, use a text editor to 
#	delete the # at the beginning of the *Define statement, and 
#	change the defined value as necessary.
#---------------------------------------------------------------------------#

#---------------------------------------------------------------------------#
# Viewstation auxillary file names
#---------------------------------------------------------------------------#

*Define HELPFILE	"VIEW.HLP"
*Define PDTFILE		"VIEW.PDT"
*Define PRNCONFIG	"VIEW.PRN"

#---------------------------------------------------------------------------#
# If the aspect ratio of your drawings look distorted, you can correct the
# aspect ratio. Common settings for standard graphics cards are:
#	VGA	 use 1.00
#	EGA	 use 1.33
#	Hercules use 1.50
# This value represents (sizey/sizex) of a square. See READ.ME file.
# Normally, the ASPECTRATIO is automatically set by Viewstation.
#---------------------------------------------------------------------------#

#*Define ASPECTRATIO	1.00

#---------------------------------------------------------------------------#
# DWGVIEW defines the initial view of each drawing when it is
# loaded and drawn for the first time. 
# Valid values are: (be sure to include the colon)
#
#	ZoomDefault:	zoom to the default view when drawing last saved
#	ZoomExtents:	zoom to include all entities
#	ZoomLimits:	zoom to the drawing limits
#	ZoomAll:	zoom to the union of limits and extents
#
#---------------------------------------------------------------------------#

*Define DWGVIEW		ZoomDefault:


#---------------------------------------------------------------------------#
# Change DWGPATH if you want viewstation's Load File dialog box to
# to default to a specific drawing directory, rather than the current
# directory when you start the program.
# For example, if your drawings are stored in directory D:\DWG, add:
#
#	*Define DWGPATH		"D:\\DWG\\"
#
# NOTICE: Use Double-Backslashes within double-quotes
#---------------------------------------------------------------------------#


#---------------------------------------------------------------------------#
# Drawing View Control Parameters
# You can change the following parameters to select between speed versus
# accuracy of the cad drawing display. Acceptable values are OFF or ON, 
# unless otherwise noted.
#
#	Linetype	- if OFF, all linetypes are shown as CONTINUOUS
#	Fill		- if OFF, only the outlines are shown
#	Curve		- if OFF, only the control points are plotted, not
#				the detail curve points
#	Width		- if OFF, all lines are drawn single width
#	Text		- if OFF, no text is displayed, ON: text shown in font
#				specified, or SIMPLE: text shown in internal 
#				SIMPLEX font. Note that Text OFF also disables
#				SHAPEs and ATTRIBUTES
#	Shape		- if OFF, no shapes are displayed
#	Attrib		- if OFF, no block attributes are displayed
#	Greek		- if OFF, no greeking performed; ON: enables greeking,
#				text and shapes smaller than GreekSize are not
#				drawn;
#	GreekSize	- number specifies pixel size of text to be greeked
#	HideLayers	- if ON, all layers are drawn, even if "hidden"
#	HideFrozen	- if OFF, frozen layers are ignored and not drawn;
#				if ON, they are treated as THAWED
#	Clip		- if ON, clipping is enabled (entities off screen are
#				not processed). Should always be ON.
#	ShxNotify	- if OFF, the user is not notified when a SHX font 
#				file is not found while reading the drawing
#	Circle		- number specifies number of chords used to draw a
#				circle. A value of 24 draws 15 degree chords
#				(360/24 = 15), is sufficient for most video
#				display modes. A value of 72 produces 5 degree
#				chords, for very smooth circles and arcs on 
#				hardcopy.
#				
#---------------------------------------------------------------------------#

# Screen Drawing Control (optimized for speed)
*New DwgControl screenControl {

	SetCntlLinetype:	ON
	SetCntlFill:		ON
	SetCntlCurve:		ON
	SetCntlWidth:		ON
	SetCntlText:		ON
	SetCntlShape:		ON
	SetCntlAttrib:		ON
	SetCntlGreek:		OFF
	SetCntlGreekSize:	4
	SetCntlHideLayers:	ON
	SetCntlHideFrozen:	ON
	SetCntlClip:		ON
	SetCntlShxNotify:	OFF
	SetCntlCircle:		24
}

# Print Drawing Control (optimized for accuracy)
*New DwgControl printControl {

	SetCntlLinetype:	ON
	SetCntlFill:		ON
	SetCntlCurve:		ON
	SetCntlWidth:		ON
	SetCntlText:		ON
	SetCntlShape:		ON
	SetCntlAttrib:		ON
	SetCntlGreek:		OFF
	SetCntlGreekSize:	4
	SetCntlHideLayers:	ON
	SetCntlHideFrozen:	ON
	SetCntlClip:		ON
	SetCntlShxNotify:	OFF
	SetCntlCircle:		72
}

#---------------------------------------------------------------------------#