BURNIN ERROR MESSAGES
                             =====================
          
          INTRODUCTION
          ============
          
          If there's something wrong with your system, you'll find
          error numbers listed in your BURNIN.LOG file, which you can
          read from the Utilities menu. Not all errors mean that
          something is wrong with your hardware, but here's a list of
          the most common messages you're likely to see.
          
          Not all errors allow BurnIn to continue to run. Some errors
          are fatal, and don't allow writing to the BURNIN.LOG file.
          These are DOS errors, and are beyond the scope of this
          summary, aside from the few descrived at the end of this
          file. If the program dies, leaving you with a cryptic DOS
          error number, consult your DOS manual for more information
          about the reason for the error, or consult your dealer.
          
          A USER ERROR
          ============
          
          If you see this on your screen:
          
          Insert disk for drive ?:
          Press any key to continue
          
          it means that you've specified a LOGICAL drive in your file
          list. You can't do that with BurnIn. What's a LOGICAL drive?
          It's either drive B: on PCs with one floppy drive, or a
          drive created with DRIVER.SYS in DOS version 3.x. Since DOS
          always asks for a disk, each time the drive is called,
          BurnIn can't cope with these drive designations. Simply
          click on that drive under the Drive menu to disable it.
          
          Here are the other errors, by number:
          
          ERROR 5
          
          This indicates an internal error within BurnIn. If you see
          this error, contact the author as soon as possible so he can
          correct the problem.
          
          ERROR 7
          
          Out of memory. There is not enough memory available for
          BurnIn to perform its routines. Try removing any memory-
          resident (TSR) programs you have installed.
          
          ERROR 25
          
          This error may occur if your printer is turned off or if it
          is OFF LINE. Correct by putting the printer on line, or by
          turning off the printer test option.
          
          ERROR 53
          
          The file BurnIn needs cannot be found. See ERROR 64 for more
          information.
          
          ERROR 57
          
          This error indicates that the device being written to had an
          input/output (I/O) error. The program cannot recover from
          this error, which will appear on your screen, rather than in
          the BURNIN.LOG file.
          
          ERROR 61
          
          This error means that the disk you're using is full, or
          doesn't have enough space to allow BurnIn to write data
          files to it. If this occurs while working with a hard disk,
          you may have more than the 127 files allowed on the hard
          disk's root directory. Remove some files, then try again.
          
          ERROR 64
          
          This error means that a file which BurnIn was trying to load
          could not be found. Check your program to make sure you have
          set the correct Path for BurnIn's data files. You can also
          use the DOS SET command before running BurnIn to set this
          information.
          
          ERROR 67
          
          Too many files in the directory being written to. Reduce the
          number of files, or change directories on the drive in
          question.
          
          ERROR 68
          
          This indicates that the device being tested either is off
          line or does not exist. Correct and retry.
          
          ERROR 70
          
          The disk being written to is write-protected. Remove the
          write-protect tab, or move the write-protect button, then
          try again.
          
          ERROR 71
          
          The floppy disk drive indicated has its door open or there
          is no diskette in the drive. Correct before repeating the
          test.

          ERROR 72
          
          The program has found a flaw on the disk being written to.
          If it's a floppy disk, insert a fresh, formatted disk in the
          drive. If it's a hard disk, you may have a bad spot on the
          disk. Back up your data, then do a fresh low-level format on
          the disk. WARNING:  DO NOT FORMAT YOUR DISK WITHOUT A
          COMPLETE BACKUP. ALL DATA WILL BE DESTROYED!        
          
          ERROR 76
          
          BurnIn can't find the file it needs, due to incorrect path
          information. If you've used the SET command to establish a
          path for BurnIn data files, check your typing.
          
          
          DOS ERRORS
          ==========
          While I can't give you information on all DOS errors, here
          are a few you may see if your computer is sick. NOTE: Exact
          wording of these messages may vary between DOS versions.
          
          PARITY ERROR
          
          This error means that there is a problem with your PC's
          memory. You must correct this error before proceeding. See
          your dealer.
          
          SEEK ERROR DRIVE ?:
          
          This is an error that indicates that your hard disk is
          seriously ill. See your dealer or use a hard disk diagnosis
          program.
          
          DRIVE ?: NOT READY 
          
          You don't want to see this error. It means that your PC
          simply doesn't recognize your hard disk at all. Contact your
          dealer or a certified technician.