;--------------------------------------------------------------------; ; Kmail Configuration File ; ;--------------------------------------------------------------------; ; Max line length is 70 chars. Comments are indicated by a semicolon ; ; in column one. Blank lines to improve readability are ok too. ; ;--------------------------------------------------------------------; ; All parms *MUST* begin in column 1. ; ;--------------------------------------------------------------------; ;--------------------------------------------------------------------; ; The values in parms 1-4 are placed into the CONTROL.DAT file ; ; within the .QWK mail packet to conform to standards. Parm (1) is ; ; displayed to the user by some offline RDR's. Limit the line length ; ; to about 40 characters or it won't fit in the space allocated. ; ;--------------------------------------------------------------------; ;------------------------------------------------; ; Parm 1 - BBS Name, displayed by RDR's ;------------------------------------------------; Produced by Kmail via Twin Peak's BBS ;------------------------------------------------; ; Parm 2 - City, State, Zip ;------------------------------------------------; Longmont, Co., 80501 ;------------------------------------------------; ; Parm 3 - BBS Phone Number ;------------------------------------------------; (303)-651-0225 ;------------------------------------------------; ; Parm 4 - Sysop Name (mixed case ok) ;------------------------------------------------; Ken Krueger, Sysop ;------------------------------------------------; ; Parm 5 - Mail Packet Name, 8 chars max. ; NO .EXT (UPPER CASE ONLY). ;------------------------------------------------; TWINPEAK ;------------------------------------------------; ; Speed=ConnectBPS,Conf-Limit,Total-Limit ;------------------------------------------------; ; Where: ConnectBPS= The modem carrier connect ; speed. (not port speed). ; ; Conf-Limit= Maximum number of messages ; per conference. ; ; Total-Limit= Total overall # of messages ;------------------------------------------------; Speed=300,15,50 Speed=1200,50,200 Speed=2400,150,400 Speed=4800,200,600 Speed=9600,200,900 Speed=14400,200,1500 Speed=Local,300,1000 Speed=Qnet,500,2000 ;------------------------------------------------; ; Protocol BAT file names ;------------------------------------------------; ; RX=Xmodem sum Receive BAT ; RC=Xmodem crc Receive BAT ; RO=Xmodem-1K Receive BAT ; RY=Ymodem Receive BAT ; RG=Ymodem-g Receive BAT ; RZ=Zmodem Receive BAT ; ; SX=Xmodem sum Send BAT ; SC=Xmodem crc Send BAT ; SO=Xmodem-1K Send BAT ; SY=Ymodem Send BAT ; SG=Ymodem-g Send BAT ; SZ=Zmodem Send BAT ;------------------------------------------------; ; Note: Deleting an entry here will remove the ; coorsponding protocol on the menu screen. ;------------------------------------------------; RX=PCBRX.BAT RC=PCBRC.BAT RO=PCBRO.BAT RY=PCBRY.BAT RG=PCBRG.BAT RZ=PCBRZ.BAT SX=PCBSX.BAT SC=PCBSC.BAT SO=PCBSO.BAT SY=PCBSY.BAT SG=PCBSG.BAT SZ=PCBSZ.BAT ;------------------------------------------------; ; Optional - Delete this section if you ; do not intend to support Puma. ;------------------------------------------------; ; PUMA Protocol Transfer Options ;------------------------------------------------; ; RP=Puma Receive BAT ; SP=Puma Send BAT ;------------------------------------------------; RP=PCBRP.BAT SP=PCBSP.BAT ;------------------------------------------------; ; Optional - Delete this section if you ; do not intend to support BiModem. ;------------------------------------------------; ; BiModem Protocol Transfer Options ;------------------------------------------------; ; RB=BiModem Receive BAT ; SB=BiModem Send BAT ;------------------------------------------------; RB=PCBRB.BAT SB=PCBSB.BAT ;------------------------------------------------; ; Qnet_Private=Yes/No ;------------------------------------------------; ; This option if set to Yes will allow a caller ; with Network-Status to download all private ; messages, EXCEPT for comments to sysop, that ; have the ECHO flag enabled in the msg header. ;------------------------------------------------; Qnet_Private=No ;------------------------------------------------; ; Ignore_Echo=Yes/No ;------------------------------------------------; ; This option applies only to Network-Status. ; ; If set to YES will cause Kmail to ignore the ; conference ECHO flag and allow downline nodes ; the ability to import messages from conf's ; defined as NON-ECHO. ; ; If set to NO, then messages in non-echo conf's ; cannot be imported into the remote systems ; messages base. ;------------------------------------------------; Ignore_Echo=No ;------------------------------------------------; ; Qwk_Dir=Location of where QWK's are stored ; Rep_Dir=Location of where REP's are stored ;------------------------------------------------; ; Use this to specify the default path/dir for ; local processing of QWK/REP files. This would ; normally be the location where your RDR expects ; to find the these files. ;------------------------------------------------; Qwk_Dir=C:\COMM\QWK Rep_Dir=C:\COMM\REP ;------------------------------------------------; ; Zip_Opt=Any valid PKZip parameter(s) ;------------------------------------------------; ; If you need different ZIP options than the ; normal system defaults, use this option. ; ; Something like "Zip_Opt=-a -es" for example. ;------------------------------------------------; ; Scan_Upld_Only=Yes/No ;------------------------------------------------; ; When set to Yes, restricts the new file scan ; to just the public upload directory. This ; offers best performance. Specify No if your ; operation requires ALL directories be scanned. ;------------------------------------------------; Scan_Upld_Only=Yes ;------------------------------------------------; ; Buffers=nnn (Default = 120) ;------------------------------------------------; ; Specify the number of dynamic I/O buffer : blocks that Kmail should allocate. ; ; I/O buffer blocks are 512 bytes each and are ; equally split between input and output files. ; ; Tested with a value of 320 on a single node ; non-multitasking system. ; ; CAUTION: Too high a value will run you ; out of memory. ;------------------------------------------------; Buffers=120 ;------------------------------------------------; ; ARC=Yes/No ; LHA=Yes/No ;------------------------------------------------; ; Specify if you wish to support either or both ; of these arichive methods. If not specified ; the default is Yes. Specify No to remove the ; option from the menu screen. ;------------------------------------------------; ARC=Yes LHA=Yes ;------------------------------------------------; ; Mail_Waiting=Yes/No (Default = Yes) ;------------------------------------------------; ; Specify whether you want the "Mail Waiting" ; flags set when importing messages. This option ; makes Kmail run a little slower. ;------------------------------------------------; Mail_Waiting=Yes ;------------------------------------------------; ; Tag=Data for your BBS ;------------------------------------------------; ; The TAG information is intended primarily for ; systems that are part of a mail network. A TAG ; line of up to 60 characters is supported. ; ; Ex: Tag=Super BBS (303)-555-5555 - Hayes Ultra ;------------------------------------------------; ;------------------------------------------------; ; Force_Tag=Yes/No ;------------------------------------------------; ; The TAG information is normally only appended ; to messages posted in conferences that have ; the "echo" flag enabled. Use this option to ; force tagging of messages of non-echo conf's ; including Main. ;------------------------------------------------; Force_Tag=No