07-27-91

Dear Sysop :

  This is the 11th release of The Verify Door to the public. Please report
any problems or suggestions to Jim Lockhart (The author) at Page Three BBS,
Winter Springs, Florida. 407-327-8421 38.4k baud HST Node 1, or call node 2
at 407-327-4524 12/2400 baud, or by leaving mail to me in the doors confer-
ence on RIME (pc-relay).

  If you are running an HST modem, be SURE you set the parameter &S0 and
write it to your NRAM using the &W command.

  ALSO, if you have recently upgraded your HST 14.4 to v.42bis, please be
sure your S38 register is set to S38=0 or at least some low number!


   QUICK SETUP:

>>>NOTE: If you are upgrading from v1.15 , v1.16, or v1.17 please stop now
   and follow the directions contained in UPGRADE.DOC.

   If you are upgrading from a version previous to v1.15, back up your
   TCBVVER file and read on:

1. De-archive the files into any directory on your hard drive and go to
   that directory. (Ideally you would want to de-archive the door files
   to the directory from which you wish to run the door.)
       
2. Run INSTALL.BAT or SETUP18
   You might consider having a copy of the docs handy as there isn't much
   on line help within the setup program.

3. Run option #1 first to properly install the TCBV files.

4. Now run option #2 and make changes to any item that might be needed.
   Pay special attention to any line in the config that contains a path
   or user security level!!!
   Save the changes when you're happy with the configuration.

5. Copy the file DOOR to your \PCB directory. (You can re-name this file
   to whatever filename suits you)

6. Edit DOOR (or whatever you re-named it to) to tailor it to your system.

7. Set up an entry for DOOR (or whatever you named it) in PCBSETUP.

8. Test the door in local mode by logging in locally as a new user......


WHAT TO DO IF TCBV REPORTS AN ERROR

  Most errors during initial setup and testing and caused by TCBV not
being able to find one or more of the files specified in the TCBV.CNF file.
Check to be SURE path names in TCBV.CNF are fully correct (check the docs to be
sure what format is being called for).


WHAT TO DO IF YOU STILL CAN'T MAKE IT RUN!

  Please note any error codes reported if an error occurs. (Error codes are
written to ERROR.LOG) That'll make it a lot easier for me to help you quickly
find the problem should one occur. Call Page Three and leave a [C]omment to
the sysop about the exact nature of your problem including any error codes
listed in ERROR.LOG and I'll be glad to get you up and running.

  If the door doesn't seem to want to call your users back, check the log file
in the door or your caller log and see if there are some NO DIALTONE messages.
If so, you may need to change your modems X parameter to X3 instead of X4 so
that the modem does not return the NO DIALTONE result code to the door.
  This door does NOT appear to work well with some UARTS such as a few found
in internal modems. It has been running successfully on versions of the
Intel 16550, 16450, 16451, 16551, 8250, 8250a and 8250b UARTs and internal
modems mapped to the same addresses as com1-8 on the AT bus.
  If you like the door and want to keep writing future versions, please
register your TCBV as mentioned in the documentation.

>>>>>   BE CERTAIN THE DOOR WORKS ON THE SYSTEM YOU INTEND TO RUN IT ON   <<<<<
                      >>>>  BEFORE REGISTERING!!!!  <<<<