; B3MD-2.INS - BYE3 insert for Morrow Micro Decision Computers	07/30/85
;
; Pin 8 (DCD) from the modem must be connected to the USART's DSR input,
; either on the internal jumper block or in the modem connecting cable.
;
;	     Note:  This is an insert, not an overlay.
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
; 07/30/85  Restored to original format			- pst
; 03/30/85  Written for Rev 1.x and Rev 2.x boards	- Jim Sinning
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
;
; The following equate will be YES if using a later Micro Decision with
; Intel 8253 timer chip and Centronics Port.  Set NO for rev 1.x board.
;
REV2X	EQU	YES		; Yes if Centronix port and 8253 chip
				; No if Rev 1.x board
;
; The following define the port address to use
;
DPORT	EQU	0FEH		; Data port
SPORT	EQU	DPORT+1		; Status/control port
;
; NOTE: The DIP switches for Serial 2 Port must be set for 1200 baud for
; this to work.
;
	 IF	REV2X
BDPORT	EQU	0F2H		; Serial 2 Port on Intel 8253 timer
CDPORT	EQU	0F3H		; 8253 control port
MODINS1	EQU	4EH		; 8 bits, 1 stop, 16x, no parity
	 ENDIF			; REV2X
;
	 IF	NOT REV2X
BDPORT	EQU	SPORT		; Baud rate port=8251 control
CDPORT	EQU	SPORT		; Control port=8251 control
MODINS1	EQU	4FH		; 8 bits, 1 stop, 64x, no parity
	 ENDIF			; NOT REV2X
;
; The following byte selects the proper mode for the Intel 8253 timer.
; Selects counter 2, reads least significant byte then most significant
; byte, sets the square wave generator and count is binary.
;
	 IF	REV2X
CNTR2	EQU	0BEH
	 ENDIF			; REV2X
;
DAV	EQU	00000010B	; Data available
TBMT	EQU	00000001B	; Transmit buffer empty
DCD	EQU	10000000B	; Data carrier detect
;
;-----------------------------------------------------------------------
;
;
; See if we still have a carrier - if not, return with the zero flag set
;
MDCARCK:IN	SPORT		; Get status
	ANI	80H		; Check DSR bit for a carrier
	RET
;
; Disconnect and wait for an incoming call
;
MDINIT:	MVI	A,10H		; Clear DTR
	OUT	SPORT		; Causing hangup
;
	PUSH	B		; Preserve in case we need it
	MVI	B,20		; 2 second delay
OFFTI:	CALL	DELAY		; 0.1 second delay
	DCR	B
	JNZ	OFFTI		; Keep looping until finnished
	POP	B		; Restore BC
;
	MVI	A,17H		; Assert DTR so that modem
	OUT	SPORT		; Can answer phone
	CALL	UDELAY		; Added to be safe
;
	 IF	IMODEM
	CALL	IMINIT
	 ENDIF			; IMODEM
;
	RET
;
; Input a character from the modem port
;
MDINP:	IN	DPORT		; Get character
	RET
;
; Check the status to see if a character is available.	If not, return
; with the zero flag set.  If yes, use 0FFH to clear the flag.
;
MDINST:	IN	SPORT		; Get status
	ANI	DAV		; Check the receive ready bit
	RZ			; Return if none
	ORI	255
	RET
;
; Send a character to the modem
;
MDOUTP:	OUT	DPORT		; Send it
	RET
;
; See if the output is ready for another character
;
MDOUTST:IN	SPORT
	ANI	TBMT		; Check the transmit ready bit
	RZ
	ORI	255
	RET
;
; Reinitialize the modem and hang up the phone by dropping DTR and
; leaving it inactive.
;
MDQUIT:	 IF	IMODEM
	CALL	IMQUIT		; Tell smartmodem to quit
	 ENDIF			; IMODEM
;
;
; Called by the main program after caller types BYE
;
MDSTOP:	MVI	A,10H		; Turn off DTR
	OUT	SPORT
	RET
;
;-----------------------------------------------------------------------
;		     Start of rev 1.x speeds
;
; The following routine sets the baudrate.  BYE3 asks for the maximum
; speed you have available.
;
	 IF	NOT REV2X
SET2400	ORI	255		; Rev 1 doesn't support 2400 baud
	RET
;
SET300:	MVI	B,BD300
	JMP	SETBAUD
;
SET1200:MVI	B,BD1200
;
SETBAUD:MVI	A,47H		; Reset, enable Rx, DTR, Tx
	OUT	SPORT		; Rx,Tx enabled
	CALL	UDELAY
	MOV	A,B		; Recover Baud Rate Word
	OUT	BDPORT
	CALL	UDELAY		; Wait for USART
	MVI	A,17H		; ERR reset, DTR, Rx, Tx all on
	OUT	SPORT
	CALL	UDELAY
	XRA	A		; Say rate OK
	RET
;
; Values to switch the 8251 between x16 and x64 for rev 1.x boards
;
BD300	EQU	4FH		; 300 baud
BD1200	EQU	4EH		; 1200 bps
	 ENDIF			; NOT REV2X
;
;		      End of rev 1.x speeds
;-----------------------------------------------------------------------
;		     Start of rev 2.x speeds
;
	 IF	REV2X		; 300/1200/2400 baud supported
SET300:	LXI	H,BD300		; Point Divisor word
	JMP	SETBAUD
;
SET1200:LXI	H,BD1200
	JMP	SETBAUD
;
SET2400:LXI	H,BD2400
;
SETBAUD:MVI	A,CNTR2		; Select Serial 2 Counter
	OUT	CDPORT
	CALL	UDELAY
	MOV	A,L		; Send Least significant byte
	OUT	BDPORT
	CALL	UDELAY
	MOV	A,H
	OUT	BDPORT
	CALL	UDELAY
	MVI	A,17H		; ERR reset, Rx, DTR, Tx all on
	OUT	SPORT
	CALL	UDELAY
	XRA	A		; Say baud rate is OK
	RET
;
; The following data words are the Intel 8253 divisors for BDPORT
;
BD300	EQU	416		; 300 baud
BD1200	EQU	104		; 1200 bps
BD2400	EQU	52		; 2400 bps
BD9600	EQU	13		; 9600 bps
	 ENDIF			; REV2X
;
; IN8251 specific USART delay
;
UDELAY:	NOP
	NOP
	NOP
	RET
;			       end
;------------------------------------------------------